View previous topic::View next topic |
Author |
Message |
mandeep_singh_kohli SEFI Member
Joined: 29 May 2019 Posts: 11
|
Posted: Wed May 29, 2019 12:12 pmPost subject: Re: Footing |
|
|
PushkarKokane wrote: |
Respected Sir is pedestal necessary? |
if your column is pin supported, then pedestal is rarely required. But if the column is fixed at bottom you will not be able to develop the anchor bolts and anchor reinforcement in tension in the limited footing depth. |
|
Back to top |
|
|
thirumalaichettiar Silver Sponsor
Joined: 26 Jan 2003 Posts: 3552
|
Posted: Sat Feb 08, 2020 11:51 pmPost subject: |
|
|
The link is not getting the PDF file and error message is appearing. Please reload it.
Thanks.
T.Rangarajan |
|
Back to top |
|
|
B.V.Harsoda General Sponsor
Joined: 19 Jan 2009 Posts: 2328 Location: RAJKOT,GUJARAT, INDIA
|
|
Back to top |
|
|
thirumalaichettiar Silver Sponsor
Joined: 26 Jan 2003 Posts: 3552
|
Posted: Sun Feb 09, 2020 6:09 amPost subject: |
|
|
Thanks a lot Er.Harsoda. |
|
Back to top |
|
|
B.V.Harsoda General Sponsor
Joined: 19 Jan 2009 Posts: 2328 Location: RAJKOT,GUJARAT, INDIA
|
|
Back to top |
|
|
kumarip SEFI Member
Joined: 12 Feb 2020 Posts: 1
|
Posted: Wed Feb 12, 2020 6:34 amPost subject: SEFI General Discussion |
|
|
Good Information. |
|
Back to top |
|
|
VPandya General Sponsor
Joined: 09 Nov 2009 Posts: 841
|
Posted: Thu Feb 13, 2020 6:19 amPost subject: ACI DETAILING MANUAL |
|
|
Dear Er. Harsodaji,
When using American Codes ACI 318 or Steel AISC 360 , detailing manual are available . How about Indian codes : For example for ACI 318 this is available :
SP-066(04): ACI Detailing Manual-2004
DESCRIPTION 2004年版的必备资源提供es answers to many detailing questions asked by design engineers, architects, contractors, detailers, and engineering students. It is divided into three sections including �Details and Detailing of Concrete Reinforcement (ACI 315-99),� �Manual of Engineering and Placing Drawings for Reinforced Concrete Structures (ACI 315R-04),� and supporting reference data. Section 1 defines responsibilities for architects, engineers, and detailers and establishes standards of practice for both structural and placing drawings. Section 2 illustrates methods for presenting necessary design information through 50 oversized, fold-out drawings of highway and non-highway structures. Structural drawings conform to �Building Code Requirements for Structural Concrete (ACI 318-02/318R-02)� and all drawings were prepared with the assistance of the Federal Highway Administration, California Department of Transportation, and Concrete Reinforcing Steel Institute. Supporting reference data in Section 3 includes specific chapters on reinforcing bars, wires, bar supports, spirals, mathematical formulas and tables, and common symbols and abbreviations. 关键词:beams (supports); bending (reinforcing steels); bridges (structures); buildings; columns (supports); computers; concrete construction; concrete slabs; detailing; drafting (drawing); engineering drawings; fabrication; floor systems; foundations; hooked reinforcement; precast concrete; prestressed concrete; reinforced concrete; reinforcing steels; splicing; stirrups; structural design; ties (reinforcement); tolerances (mechanics); walls; welded wire fabric. TABLE OF CONTENTS Part A�Responsibilities of the architect/engineer Chapter 1�Structural drawings 1.1�General 1.2�Drawing standards 1.3�Structural drawings�Buildings and other structures 1.4�Structural drawings�Highway and transportation Structures :
Indian codes both Concrete and Steel should have published Detailing Manuals .
Note : One more thing " WHO IS RESPONSIBLE FOR DETAILING AND CONNECTION DESIGN , ENGINEER OF RECORD ( RESPONSIBLE ENGINEER ) OR CONCRETE DETAILER OR STEEL FABRICATOR ? " In US Codes a license Structural Engineer who designed the building is always responsible for Detailing and Steel Connection Design not Steel Fabricator or Concrete Detailer .
Regards .
Vasudeo Pandya P.E. Structural Engineer |
|
Back to top |
|
|
thirumalaichettiar Silver Sponsor
Joined: 26 Jan 2003 Posts: 3552
|
Posted: Thu Feb 13, 2020 1:57 pmPost subject: |
|
|
Dear Er.Vasudeo Pandya /Sir, In addition there is a detailing manual from CSRI ,USA. This also gives good detailing.
T.Rangarajan.
|
|
Back to top |
|
|
abhishek_kumar General Sponsor
Joined: 20 Mar 2012 Posts: 11
|
Posted: Mon May 18, 2020 4:04 pmPost subject: Reinforcement detailing of Joint |
|
|
Dear Seniors & fellow Sefian's,
PFA the document on reinforcement detailing of Beam Column joint.
In this paper, the conventional practices of curtailment of bars shown in Fig.5 & 6 . But curtailment of bars shown in Fig.7 & 8 are endorsed due to better performance and less congestion.
My Query is,
A.Can we use Fig 7 & 8 detailing for:-
1. Joints in RC Shear walls. 2. Joints in Walls of Rectangular Water Tanks.
B. Does anyone seen Detailing as Fig.7 & 8 in practice? Is it really advantageous?
Thanks & Regards
Abhishek kumar
Warning:
Make sure you scan the downloaded attachment with updated antivirus tools before opening them. They may contain viruses. Use online scanners
here
and
here
to upload downloaded attachment to check for safety.
|
Description: |
|
Download |
Filename: |
Reinf Detailing of Beam Column Joint.pdf |
Filesize: |
385.21 KB |
Downloaded: |
465 Time(s) |
|
|
Back to top |
|
|
B.V.Harsoda General Sponsor
Joined: 19 Jan 2009 Posts: 2328 Location: RAJKOT,GUJARAT, INDIA
|
Posted: Wed Aug 26, 2020 7:07 amPost subject: |
|
|
My comments for Commentary for Code on Ductile Design and Detailing of Reinforced Concrete Structures Subjected to Seismic Forces � Code of Practice (IS 13920:2016) sent toIAStuctE
Warning:
Make sure you scan the downloaded attachment with updated antivirus tools before opening them. They may contain viruses. Use online scanners
here
and
here
to upload downloaded attachment to check for safety.
|
Description: |
|
Download |
Filename: |
BVH Comments.pdf |
Filesize: |
926.58 KB |
Downloaded: |
296 Time(s) |
|
|
Back to top |
|
|
|